🔊 TTS Settings
Chapter 16 …
The Genius Blacksmith Obsessed Over by Hunters
“I want to use this sword somehow,” Goyo said.
“Is that not possible?”
The Hunter who had brought the sword asked in a doubtful tone.
“The request is too vague as it is. Even if the sword broke after being used, it was still used somehow. You could even keep using it with the broken edge as it is. I think your requirements need to be a little more specific.”
Gangcheol continued his explanation.
“The swords used by the Yeonhwa Guild are relatively soft, but they have their own advantages.”
At least when it came to the steel used for longswords, the softer it was—that is, the lower its hardness—the better its tensile strength.
That meant the blade dulled more easily, but it was also far less likely to snap.
On top of that, the blade itself was quite thick.
So if a thick blade dulled easily and gave the impression of being “soft,” it was actually better suited for rough handling.
“But the Yeonhwa Guild is still a new guild, isn’t it?”
“So?”
“This sword may be broken, but it’s still a product sold through the Hunter Association’s shop. You know what that means, don’t you?”
Gangcheol nodded.
The Hunter Association was famous for operating as transparently and honestly as an archery association.
Anything supplied to its stores practically came with a guarantee that its quality was at least above average.
The Yeonhwa Guild, on the other hand, was still new.
Like most newly established guilds, they lacked experience, and because the people there were rather straightforward, they were easy targets for scams.
From Gangcheol’s own assessment, they still had plenty of room for improvement, so it wasn’t an unfair criticism.
“Still, I’d rather use something that suits my preferences than a soft sword I don’t fully trust.”
Gangcheol replied,
“There’s usually a reason people choose softer blades. If you’re willing to accept the drawbacks even after hearing my explanation, then I’ll remake this broken sword into something you can use.”
He spoke slowly.
“The first thing to understand is that even blades used for woodworking have different hardness depending on where they’re used.
Countries in warmer regions, where the wood is harder, generally use softer blades.
Meanwhile, colder regions have softer wood, so they tend to use harder blades.”
If you strike hard wood, both hard and soft blades will eventually suffer damage.
That’s why blades intended for hard wood are made with lower hardness and higher tensile strength so they won’t break.
Soft wood, however, cuts easily no matter what.
So in that case, increasing hardness improves edge retention, and even though tensile strength decreases, the blade can still withstand normal use.
Having heard the explanation, the rest came down entirely to personal preference.
The Hunter seemed to think it over for a moment before saying,
“Even so… I’d still like to use a hard blade.”
“Very well. I’ll make it that way. If possible, I’d like to borrow an office for a moment.”
At Gangcheol’s request, the Hunter who had commissioned the work, along with several others, led him to an office.
“You’re free to use anything on this desk. If you need something, just ask.”
“Oh, I think this will be enough.”
The room was a little messy, but it had almost everything he needed.
What actually surprised Gangcheol was something else.
A drafting table, scale rulers, and all kinds of writing utensils…
The whole place looked so rugged that it was difficult to distinguish it from a construction site.
It wasn’t what he’d expected to see inside a guild.
“I have a pencil. I just need some paper. A3 size would be ideal.”
“Oh, there’s a box of scrap paper over there, and new paper is on that shelf.”
“Scrap paper is fin… Huh?”
The moment Gangcheol picked up a sheet, he clicked his tongue once again.
No wonder the place felt like an architectural office.
The backs of the papers actually had architectural blueprints drawn on them.
By hand, no less.
“You draw blueprints at the guild?”
“Of course.”
“By hand instead of using CAD?”
“CAD was too difficult to learn.”
What a truly strange person.
“…Well then, let’s first think about how to use the broken piece.”
The first step was to sketch a rough design.
Since he was repurposing an already existing blade, the sketch was even more important than usual.
The initial draft needed to be as detailed as possible and as close to the finished product as it could be.
Gangcheol muttered inwardly.
‘Eye of Form.’
Length.
Width.
Thickness.
Bevel angle.
Tip angle.
Information about the broken blade appeared before Gangcheol’s eyes.
“Let’s start with the broken piece…”
His hand began to move.
As his pencil traveled across the paper, lines appeared one after another.
A few seemingly casual strokes soon formed the exact silhouette of the broken blade.
Thanks to Eye of Form, every line landed precisely where it belonged without him ever touching a ruler.
“Damn… He’s not a blacksmith—he’s an artist.”
Ignoring the amazed reactions around him, Gangcheol remained absorbed in his work.
“Now that I’ve drawn it, I can roughly see what it should become.”
“About twenty centimeters?”
“Just under twenty-five. Calling it twenty-five centimeters wouldn’t be wrong.”
The blade measured about five millimeters thick and just under thirty millimeters wide.
A piece this size could easily be reforged into a fixed knife intended for rough work.
It wouldn’t serve as a primary weapon, but it would be perfect for pulling from one’s belt to perform delicate tasks such as field-dressing monsters after defeating them.
“If we sacrifice about ten centimeters of the blade to make the tang and keep the blade as wide as possible while thinning it down, it’ll be a very usable knife.”
“Wouldn’t that make it too small?”
“If it isn’t meant to be used as a weapon, it doesn’t need to be long. Even for combat knives, six or seven inches—about fifteen to seventeen and a half centimeters—is considered standard. For a work knife, even ten centimeters would be fine, though I doubt that’s what you want.”
“Hm… Then please make the blade fifteen centimeters.”
Gangcheol continued murmuring to himself while adding more details to the sketch.
Every time his pencil moved, the handle changed shape.
A guard appeared…
Then disappeared…
Finally, Gangcheol set the pencil down and handed the drawing to the Hunter.
“This is roughly what it’ll look like. What do you think?”
“I’d like the blade to be a little longer.”
He still hadn’t given up on preserving as much of the original blade as possible.
Gangcheol shook his head.
“If the tang gets too short, it’ll become vulnerable to impact. If you managed to break a longsword, I doubt you’re exactly gentle with your equipment. Please compromise a little for the sake of durability.”
“Hmm… All right.”
“Great! Then I’ll have it finished by tomorrow afternoon.”
The Hunter nodded and left.
“Well then…”
Gangcheol alternated his gaze between the broken blade and the sketch.
Since he was modifying an existing item rather than forging one from scratch, he had to pay much closer attention to the order of operations.
Otherwise, the heat generated during grinding could ruin the blade’s heat treatment.
“The heavy grinding should come first.”
In other words, shaping the tang that would fit into the handle came before everything else.
The first step was to mark the areas to be ground with a board marker.
Then he quickly ground away every marked section until no ink remained and the surface became perfectly even.
From time to time, he dipped the overheated blade into water before blasting it with compressed air to cool it rapidly.
“Next comes thinning.”
Keeping the blade wet with water, he ground along the existing bevel.
His goal was to make the blade itself as thin as possible before forming the cutting edge.
Among everything he had to do, this was the most difficult part.
Should I just take the easy route…?
After a brief moment of hesitation, Gangcheol shook his head.
He couldn’t skip this step.
The things users noticed most while using a knife were the feel of the handle and how effortlessly the blade bit into its target.
Thinning dramatically improved that cutting sensation.
“Whew… Let’s do it.”
Gangcheol pressed the blade against the grinder.
Shhhhk…
Shhhhhhk…
The sound was completely different from before.
This wasn’t a process where visible progress happened quickly.
Precisely because of that, it demanded absolute concentration.
The blade had to be ground paper-thin.
There was no room for mistakes.
He had to match the bevel angle perfectly in a single attempt.
“Good.”
After checking the grind marks, he resumed.
He moved slowly and evenly, making sure no section was ground excessively.
His movements looked as though he were merely brushing the blade against the grinder’s belt.
After repeating the motion several times, the edge became so thin that merely touching it to a whetstone would form a razor edge.
Satisfied, Gangcheol turned off the grinder.
Only the simple tasks remained.
Making the handle, in particular, was easy enough that more than half the time would simply be spent waiting.
Compared to shaping steel, carving wood was almost laughably easy.
Carving a slot for the tang was something he could practically do with his eyes closed.
Once that was done, he applied adhesive, fitted the two pieces together perfectly, and secured everything tightly with rubber bands while the glue cured.
“Sharpening won’t take long either. It’s carbon steel.”
Thanks to the thinning process, creating the edge took only moments.
—Looks like all the effort you put into flattening the bevels paid off.
“Of course. Once it’s done properly, maintenance becomes much easier for quite a while.”
Even without Gangcheol personally maintaining it, future sharpening would be far easier.
After finishing the sharpening, he still had time left.
Perhaps because he was bored, he picked up the longsword and examined it.
“Maybe I’ll adjust the tip a little.”
Since the blade had clearly been used primarily for cutting rather than thrusting, he reshaped the point to preserve as much blade width as possible, maximizing cutting performance.
Normally, knife tips curved upward toward the spine.
But if the point angled slightly downward toward the edge, the effective cutting section became just a little longer.
—You’re not shortening the handle?
“If he wanted that, he would’ve asked. There’s no reason for me to do extra work he didn’t request.”
—Then are we done for the day?
Gangcheol wiped away his sweat and seemed about to clean up the workbench…
Then paused.
“…No. Since the blade got shorter, I think there’s still something I should do.”
Turning back around, he switched the grinder on once again.
—You’re seriously unbelievable.
Late into the night, the sound of machinery continued echoing throughout the Yeonhwa Guild.
The next day.
“Let’s see if it’s bonded properly.”
Bang! Bang! Bang!
Gangcheol slammed the handle attached to the blade against a solid surface.
It held firmly without coming loose.
“Now it’s time to shape it.”
Unlike the painstaking custom work he’d done on Gwon Semi’s sword, this handle was carved into a comfortable, all-purpose shape suitable for anyone.
It was oval in cross-section, with the rear slightly wider and thicker than the front.
—Isn’t it a little too thin?
“I’ve got a plan.”
Gangcheol took out two items.
One was tsuka-ito, the cotton cord traditionally used to wrap Japanese sword handles.
The other was paracord, commonly known as parachute cord.
He spread adhesive along the sides of the handle before tightly wrapping the paracord around it.
Then, just like wrapping the handle of a Japanese sword, he wound the tsuka-ito over it, crossing the knots one after another.
“There.”
After securing the wrapping with clamps, he moved to the drill press.
Grrrrrk! Grrrrrk! Grrrrrrrrk!
In an instant, three holes had been drilled through the handle.
The hole at the butt of the handle was large.
The two holes in the middle were smaller.
Screws were tightened through the smaller holes.
The larger hole allowed the cords to pass through before being tied into a knot.
With that, the knife was complete.
The handle wrapping resembled that of the longsword, but unlike the longsword—which used ray skin beneath the wrapping—this one had tightly wound paracord with its inner core removed.
“Almost done!”
Though he called it “almost,” the knife already looked remarkably impressive.
Not long afterward, the Hunter who had commissioned the work came rushing in.
Gangcheol had only called him a short while ago, yet it seemed the man had been waiting nearby the whole time.
“Is it finished?”
“I still have to make the sheath. I called you to ask about that. I can’t just hand you a bare knife.”
Even though the sheath remained unfinished, the Hunter didn’t seem to mind.
“It already looks amazing. May I hold it?”
“Let’s settle the sheath first.”
“I’d like it made from monster hide. It’s from a mutant orc. It looks hard on the outside, but…”
After hearing the explanation, Gangcheol nodded.
“Ah, so that’s what it is.”
“You’ve worked with it before?”
“Yes. You soak it in hot water, shape it, and once it dries, it hardens. Just like plastic or Kydex.”
The answer came without the slightest hesitation.
The Hunter’s doubtful expression disappeared, replaced by eager anticipation.
“Then… can I finally hold it now?”